How to maintain the electric pick, what kind of oil it USES.
I. regular replacement and addition of professional grease:
The hammer/pick can work normally for 60 hours (it depends on different users), and the cylinder should be replaced with 30 grams of special grease. Yahu. Y. Wild xushuguan easy imported special synthetic high temperature lubricating grease lubrication, with 30 ° c to 130 ° c temperature high temperature normal startup performance, in order to ensure the hammer/demolition hammer hammer to maximize efficiency, please do not add any brand in the hammer/electric pick oil! If the oil is added into the pick by mistake, it will result in serious oil leakage and weak impact of the machine.
Ii. Adding method of cylinder grease:
1, first of all, the machine has been removed from the deterioration of grease (such as: cylinder, piston, cylinder box and other parts of the deterioration of the old grease);
2. Then, evenly apply the "yahu. Y.
3. Finally, pay attention to ensure that the vent or vent of the following components are unimpeded, so as to avoid the phenomenon of hammer weakness or broken hammer caused by the blocking of the vent:
※ ram -- make sure that the two grooves at the bottom of the ram hole are not blocked by grease and must be completely exposed.
※ piston -- make sure you have four pistons. 4,? 2. The vent is unimpeded.
Cylinder -- make sure that the 6 exhaust grooves on the inner surface of the cylinder box are exposed.
Protection of clamping seat
The correct use of the clamping seat is helpful to further extend the service life of the machine. Therefore, it is recommended that you never use the flat chisel as a crowbar in the chipping process, especially force the pick to open the broken objects, so as not to cause the fracture of the clamping part of the head of the pick and affect your normal use.
Iv. Motor maintenance
1. Before using the machine, pay attention to observe whether the motor inlet and outlet are unobstructed! In order to avoid damage due to poor heat dissipation motor stator, rotor.
2. Replace the carbon brush in time and use the carbon brush provided by the original factory! Using a mismatched carbon brush can easily damage the commutator.
3. When using the machine for a long time, if the impact force is obviously weakened, please timely replace the o-ring on the piston and the hammer; And timely supplement, add "yahu. Y. Hu yi special lubrication grease"!
4. When repairing and disassembling, pay attention to timely replace the seal ring that has been out of shape and damaged! So as not to cause oil loss and leakage.
V. difference between grease and oil lubrication:
For the electric pick lubricated with grease, because the grease is a solid glue, it needs a period of time to warm up before work, so that the grease can be fully lubricated and melted, and the impact force of the electric pick can reach the best state instantly.
Advantages (grease) : good sealing, sufficient lubrication, good for protecting cylinders and pistons, and prolonging the service life of electric picks. The longer the working time, the better the sealing, lubrication, hammering force will continue to increase, the more powerful the use.
Disadvantages (grease) : it takes about 2 minutes to warm up the machine (when the ambient temperature is too low, the operating time should be extended appropriately). The oil of an electric pick is liquid, so it does not need to melt after starting up, and can work immediately.
Pros (oil) : no need to melt at startup, can immediately work.
Disadvantages (oil) : poor sealing and lubrication performance, easy oil leakage. The longer the working time of the hammer/pick, the less the sealing and lubricity, and the less the impact force.
I. regular replacement and addition of professional grease:
The hammer/pick can work normally for 60 hours (it depends on different users), and the cylinder should be replaced with 30 grams of special grease. Yahu. Y. Wild xushuguan easy imported special synthetic high temperature lubricating grease lubrication, with 30 ° c to 130 ° c temperature high temperature normal startup performance, in order to ensure the hammer/demolition hammer hammer to maximize efficiency, please do not add any brand in the hammer/electric pick oil! If the oil is added into the pick by mistake, it will result in serious oil leakage and weak impact of the machine.
Ii. Adding method of cylinder grease:
1, first of all, the machine has been removed from the deterioration of grease (such as: cylinder, piston, cylinder box and other parts of the deterioration of the old grease);
2. Then, evenly apply the "yahu. Y.
3. Finally, pay attention to ensure that the vent or vent of the following components are unimpeded, so as to avoid the phenomenon of hammer weakness or broken hammer caused by the blocking of the vent:
※ ram -- make sure that the two grooves at the bottom of the ram hole are not blocked by grease and must be completely exposed.
※ piston -- make sure you have four pistons. 4,? 2. The vent is unimpeded.
Cylinder -- make sure that the 6 exhaust grooves on the inner surface of the cylinder box are exposed.
Protection of clamping seat
The correct use of the clamping seat is helpful to further extend the service life of the machine. Therefore, it is recommended that you never use the flat chisel as a crowbar in the chipping process, especially force the pick to open the broken objects, so as not to cause the fracture of the clamping part of the head of the pick and affect your normal use.
Iv. Motor maintenance
1. Before using the machine, pay attention to observe whether the motor inlet and outlet are unobstructed! In order to avoid damage due to poor heat dissipation motor stator, rotor.
2. Replace the carbon brush in time and use the carbon brush provided by the original factory! Using a mismatched carbon brush can easily damage the commutator.
3. When using the machine for a long time, if the impact force is obviously weakened, please timely replace the o-ring on the piston and the hammer; And timely supplement, add "yahu. Y. Hu yi special lubrication grease"!
4. When repairing and disassembling, pay attention to timely replace the seal ring that has been out of shape and damaged! So as not to cause oil loss and leakage.
V. difference between grease and oil lubrication:
For the electric pick lubricated with grease, because the grease is a solid glue, it needs a period of time to warm up before work, so that the grease can be fully lubricated and melted, and the impact force of the electric pick can reach the best state instantly.
Advantages (grease) : good sealing, sufficient lubrication, good for protecting cylinders and pistons, and prolonging the service life of electric picks. The longer the working time, the better the sealing, lubrication, hammering force will continue to increase, the more powerful the use.
Disadvantages (grease) : it takes about 2 minutes to warm up the machine (when the ambient temperature is too low, the operating time should be extended appropriately). The oil of an electric pick is liquid, so it does not need to melt after starting up, and can work immediately.
Pros (oil) : no need to melt at startup, can immediately work.
Disadvantages (oil) : poor sealing and lubrication performance, easy oil leakage. The longer the working time of the hammer/pick, the less the sealing and lubricity, and the less the impact force.